HPT Products
Products
technical information
 
Call to Order
 
Repair and Services
Quick Contact

DLE30 Air Driven Gas Booster

DLE30 Air Driven Gas Booster
DLE 30 Arrangement Drawing
+
DLE 30 Arrangement Drawing

 

This email address is being protected from spambots. You need JavaScript enabled to view it. RFQ Icon

Maximator Air Driven Gas Boosters suitable for boosting Most inert Gases such as : Nitrogen, Oxygen, CO2, Helium, Argon, Xenon and many more

Technical Data

PRESSURE RATIO 30:1
COMPRESSION RATIO 20:1
SUPPLY PRESSURE(PSI) MIN.* 220
MIN.** 440
MAX 8700
MAX OUTLET PRESSURE(PSI) 8700
STALL PRESSURE 30Pa+Ps
AIR DRIVE PORT 1/2"NPTF
PILOT PORT 1/8"NPT
CONNECTIONS INLET 9/16"-18 (1/4"HP)
OUTPUT 9/16"-18 (1/4"HP)
MAX CYCLE RATE 120
DISPL PER CYCLE (IN3) 7.3
MAX TEMP. F 210
WEIGHT (LBS) 40
NOTE:
* = Minimum required for basic operation
** = Minimum required to achieve maximum outlet pressures
Pa = Drive air pressure, 145 psi maximum, 15 psi minimum
Ps = Gas supply (suction) pressure
The 9/16-18 is a 1/4" O.D. tubing, high pressure coned and threaded connection.
Stall pressure must not be allowed to exceed outlet pressure rating.
Compression ratio is the minimum required ratio of outlet pressure/supply pressure.
Adapter (MT30-21NFBHM4) is available to convert the 9/16"-18 connection to 1/4" FNPT. Order separately.

 

  • Pressures to 30,000 for most gases and 5,000 for oxygen
  • Easy to install and operate
  • Compact, lightweight design
  • Single or double acting and two stage models
  • Double air head available in single and two stage boosters
  • No electrical power required
  • Requires no lubrication
  • Boosters are contaminant free
  • Units can be operated in series or parallel
  • Variety of pressure and compression ratios available
  • High pressure gas testing or process qualification
  • Charging of accumulators
  • Boosting gas pressures from nitrogen or Oxygen bottles and generators
  • Nitrogen injection for molding machines
  • Leak detection systems
  • pressure autoclaving
  • Typical Gases - air, nitrogen, helium, oxygen, carbon dioxide, nitrous oxide, neon, argon, hydrogen, carbon monoxide, methane, ethylene and natural gas

All gas boosters are available with an optional air control unit (-ACP). This package is shown below and consists of an air filter, regulator with gauge, shutoff valve and necessary fittings and hose for plumbing unregulated pilot port

HPT offers a wide variety of other accessories to assist the installation of your Maximator gas booster.

  • Gas receivers
  • Pressure gauges
  • Air pilot pressure switches
  • Filters
  • High pressure valves, fittings and tubing
  • Miscellaneous plumbing components
  • DAS: Dry Air Spool
  • DASR: Dry Air Spool Modification, Pressure Reducing Regulator with Gauge and Relief Valve (For Driving Booster From N2 Gas Bottle)
  • TR: Timer Relay (Operator Can Control The Cycles Per Minute)
  • NBR: Change Seals to Nitrile Buna Rubber (For Use With CO2)
  • O2: Oxygen Cleaning & Modifications (For Use With Oxygen)
  • H2: Oxygen Cleaning & Safe Ventilation & Purging Modifications (For Use With Hydrogen)
  • SGD: Sour Gas Modification (For Driving With Sour Gas)
  • LT: Low Temperature Modification (For Use In Sub Artic Conditions)
  • HT: High Temperature Modification For Temperature of 120 °C (For L or LSF Pumps)
  • EPOXY: Epoxy Coat Booster (For Offshore Applications)

 

DLE 30 Flow Chart

60 psi Air Drive

DLE30 Pressure 60psi
+

80 psi Air Drive

DLE30 Pressure 80psi
+

100 psi Air Drive

DLE30 Pressure 100psi
+

4 Bar Air Drive

DLE30 Pressure 4 Bar
+

6 Bar Air Drive

DLE30 Pressure 6 Bar
+

8 Bar Air Drive

DLE30 Pressure 8 Bar
+

 

GAS BOOSTER SAMPLE FLOW RATES (SCFM)

CATALOG
NUMBER
Pa=90 PSI
Ps
Po
F
DLE30
500
1,000
8.28
DLE30
500
3,000
1.08
DLE30
1,250
1,500
21.30
DLE30
1,250
3,000
11.40
NOTE:
Maximum air drive pressure is 145 psi.
Minimum air drive pressure is 15 psi.
Pa = Drive air pressure (psi)
Ps = Gas supply pressure (psi)
Po = Gas outlet pressure (psi)
F = Gas flow (SCFM)
Drive air pressure operating range is 15-145 psi. Flows above are with 90 psi air drive, unless noted.
Drive air flow requirements are up to 70 SCFM per air head, and up to 280 SCFM (total) for 8DLE models. Reduced air drive flow will produce lower gas flow.
Drive air should be filtered to between 5µ and 40µ and have a dew point between 0°F and 50°F.
Consult HPT for performance values on specific application parameters.

Bundle This Booster As A System

(Contact HPT for a system designed specific for your Application)

Gas Booster Systems

Gas Booster Systems
 

Gas Booster Systems provide a turnkey solution for customers wishing to increase their industrial gas pressures. Offered in several standard formats these systems provide a compact, portable source for increasing gas pressures. HPT Air Driven Gas Booster Systems are shipped assembled and fully tested, ready for installation. HPT Gas Booster Systems are capable of compressing most gases including nitrogen, argon, helium and hydrogen up to 36,000 psi.

Know More

Nitrogen Boosters with Pressure up to 36,000 psi

Gas Booster Systems
 

Nitrogen booster packages offer an economical method of boosting nitrogen (or other select gases or air) gas pressure up to 36,000 psi. HPT nitrogen booster package features a compact and lightweight arrangement that is turn-key and fully tested. Single and double acting nitrogen gas booster pumps are available to meet flow rate requirements. Maximator high pressure nitrogen booster pumps are capable of increasing pressures as low as 30 psi to pressures as high as 36,000 psi. Two stage nitrogen gas boosters are available for low to high pressure applications.

Oxygen Boosters

Gas Booster Systems
 

Oxygen Booster pumps are small, lightweight and economical. Oxygen gas booster packages are ideal for aircraft and bottle filling applications. Typical oxygen booster pumps are for boosting pressures up to 2,000 psi often required in the airline ground support industry and up to 3,000 psi for the diving market. However packages can be provided utilizing any of our gas boosters with maximum pressures of 5,000 psi. Single and double acting oxygen boosters are available at High Pressure Technologies to meet flow rate requirements.